News archive April 2018 - Koos van den Hout

Archive by year: 1999 | 2000 | 2001 | 2002 | 2003 | 2004 | 2005 | 2006 | 2007 | 2008 | 2009 | 2010 | 2011 | 2012 | 2013 | 2014 | 2015 | 2016 | 2017 | 2018 | 2019 | 2020

2018-04-26 More radio maps and their limits 2 years ago
The PE4KH website has maps of the locations where I contacted radio amateurs all over the world. The maps with generated images are created by exporting my locators worked/confirmed from cqrlog and using gcmwin for linux with a whole set of different configurations to plot the results.

But now the 2 meter band has been added and on that band a 'record distance' is not as far as on HF. On HF my current distance record was a contact with Australia at 16581 kilometers. My current distance record on the 2 meter band is 363 kilometer in Germany. Quite a different scale!

So the maps part has been enhanced with a 2 meter contacts map, but gcmwin can't use 6-position maidenhead locators so the map is quite coarse compared to what I want. I don't know the solution at the moment to improve this. The recent qso map PE4KH does show the more precise gridsquares when available in the log, so maybe that page needs distances added.
Read the rest of More radio maps and their limits

Tags: , ,
2018-04-24 KVM and os-specific defaults 2 years ago
Today I wanted to install a new virtual machine on the new homeserver and virt-install gave me a new warning:
WARNING  No operating system detected, VM performance may suffer. Specify an OS with --os-variant for optimal results.
According to the virt-install manpage the --os-variant can be found with osinfo-query os which I can't find in Devuan jessie. But the same information is available via Installing Virtual Machines with virt-install, plus copy pastable distro install one-liners.

I chose debian7 as that is probably the closest to Devuan Jessie to be upgraded to Devuan ascii immediately.

The interesting change is that the resulting linux suddenly has virtio networkcards and a disk /dev/vda. That last bit is quite different from earlier virtual machines.

Tags: , ,
2018-04-24 Building my own balun, part 7: Better measurements of the result 2 years ago
Homemade balun version 2 SWR scan 1-60 MHz
Homemade balun version 2 SWR scan 1-60 MHz 20180424
Homemade balun version 2 SWR scan 10 meter band
Homemade balun version 2 SWR scan 10 meter band 20180424
Homemade balun version 2 SWR scan 20 meter band
Homemade balun version 2 SWR scan 20 meter band 20180424
Time to do measurements of the revised attic antenna. And now with a voltage balun with more windings the balun is working better, showing ok SWR values. A nice optimum in the middle of the 20 meter band (although I originally wanted that optimum near the digital mode part) and a nice optimum in the 10 meter band (also somewhat higher than originally planned). Comparing them to the original measurements show an increase in frequency in both SWR curves.

So I consider this a good result! Time to get it on the air and make contacts again.

Next step, working on an outside dipole with the Fritzel balun.
Read the rest of Building my own balun, part 7: Better measurements of the result

Tags: , ,
2018-04-23 Building my own balun, part 6: Redo and some success: a working antenna again 2 years ago
After the previous measurements showed the balun and dipole under the roof weren't acting as a perfect combination. So time to do a few things better: more windings, less leftover wire and a switch to a voltage balun. Yes, other sources indicate a current balun is better, but I decided otherwise. The Fritzel balun turned out to be a voltage balun after I removed it from the dipole antenna.

Balun project version 2 in case So I used the instructions at 1:1 voltage balun by VK6YSF to rebuild it as a voltage balun and I made sure the wires were shorter in the end. Getting the shorter wires in the right places in the case did get me some slightly burned fingers!

Success is currently defined as "I can transmit a carrier on the 20 meter or 10 meter band and the SWR meter of my radio only goes up a few segments" which isn't very scientific, I will need to do the rest of the measurements with the SWR meter to be sure.
Read the rest of Building my own balun, part 6: Redo and some success: a working antenna again

Tags: , ,
2018-04-20 Spam van StoryTel 2 years ago
Spam van StoryTel, waarin het me opvalt dat ze de e-mail marketing spam infrastructuur van mandrillapp gebruiken, maar zelfs zonder manieren om uit te schrijven of iets anders wat nog een beetje rekening houdt met de huidige wetgeving op dat gebied.

Zoeken op storytel spam levert niet veel vergelijkbare verhalen op dus blijkbaar is dit een nieuwe aanpak van StoryTel.

Dan maar via alle routes aangemeld als spam, inclusief een complete melding bij Spam melden bij ACM.

Tags: , ,
2018-04-16 Building my own balun, part 5: First tests of the result 2 years ago
Homemade balun SWR scan 1-60 MHz
Homemade balun SWR scan 1-60 MHz 20180415
Homemade balun SWR scan 10 meter band
Homemade balun SWR scan 10 meter band 20180415
Homemade balun SWR scan 20 meter band
Homemade balun SWR scan 20 meter band 20180415
So I removed the old balun and installed the one I made. Removing the old one wasn't easy: the Fritzel balun has a cover over the SO239 connector which makes the heavy duty connector I used very hard to unscrew. So I had to break bits of that cover to get the needed access. And the connector ended with a lot more scratches from my attempts to get access to it.

But now the balun is replaced, and measured. And it looks like some things have changed now causing the antenna to be 'mistuned'.

Update: Just some measurements and thinking: adding the big common mode choke in the mix makes the combination show better SWR curves (still not what I want) but with the frequency with the best SWR still too low. This suggests (to me) two things: I need more windings on the ferrite core and less extra wire length from the core to the connectors. Time for a rebuild.
Read the rest of Building my own balun, part 5: First tests of the result

Tags: , ,
2018-04-15 Building my own balun, part 4: Deciding on where to put dipole ends and finishing it 2 years ago
Balun, case and ferrite core Balun in open case I finally decided where to put the holes in the case for the dipole ends of the balun. This took some serious pondering!

I made those holes, put screws through them and wound the ferrite core with enamelled copper wire. To guess the needed length of wire I first wound it with packing rope, made a small knot at the point where it was enough and unwound the rope to measure the length I used and took a bit longer wire.

Using sanding paper I removed the enamel isolation from the ends of the wires and used soldering tin on it.

Other parts of this project:

Tags: , ,
2018-04-08 I participated in the EA RTTY Contest 2018 2 years ago
As planned I participated in the EA RTTY Contest edition 2018.

I had most of the time to play radio on Sunday so I decided to participate in the SO20DX (single operator 20 meter band outside Spain) category. I did make two contacts on the 40 meter band when I thought I wasn't going to find any new station the 20 meter band but I returned. And found more stations on the 20 meter band.

20 meter interference pattern
Interference pattern on the 20 meter band
Radio propagation was ok, best DX were some Asiatic Russia stations and a US station in Illinois. The local noise was bad and there were some new sources of interference active. The pattern as in the image (links to full view of the 2.5 kHz waterfall) which is very stable in frequency and has a tendency to stop and start, and at the stop the carriers move together. Also a more 'rattling' noise which sounded like an electrical problem.

In the end I made 81 contacts in total, 79 on the 20 meter band.
Read the rest of I participated in the EA RTTY Contest 2018

Tags: , , ,
2018-04-07 I'm glad you read my newsitem 2 years ago
Apr  6 23:41:16 greenblatt sshd[25116]: Invalid user squid from 139.99.122.129
Apr  7 01:44:09 greenblatt sshd[3495]: Invalid user squid from 110.10.189.108
Apr  7 08:21:37 greenblatt sshd[7106]: Invalid user squid from 118.24.100.11
I'm glad you read my newsitem about keeping squid running.

Tags: , ,
2018-04-06 And a contact with South Africa, new country 2 years ago
Another new country that should not be too hard to get in the log but did not happen until today: South Africa. ZS6ZA was active on 40 meter FT8 and received my answers.

Tags: , ,
2018-04-06 Keeping squid webproxy running for network mismatches 2 years ago
I considered stopping using squid when upgrading to the new homeserver but I have now changed that decision: I need to keep it running for applications that want to do http connections to IPv6-only systems but can't handle those. There are some old scripts running that need it but it's also the way to fix the problem I noticed with linuxcounter.

Tags: , ,
2018-04-06 25 years of Linux use 2 years ago
Powered by Linux In looking at a problem with the linuxcounter script I noticed I am now passing the 25 years with Linux mark. I first saw it in the beginning of 1993 when part of my internship happened at the 'expa' lab of Hogeschool Utrecht with SLS Linux.

Anyway, still using Linux a lot. It's been an interesting 25 years!

Tags: , ,
2018-04-04 I am planning to participate in the EA RTTY Contest 2 years ago
After my participation in the EA PSK63 Contest 2018 I plan to have the radio active in the upcoming weekend for the EA RTTY Contest.

Tags: , ,
2018-04-04 Building my own balun, part 3: First work on the case 2 years ago
Balun project case Balun project case The first work on the balun case was placing the SO239 socket. This included drilling a hole in the case of the right size and at the right position. Figuring out where to put it was mostly influenced by the fact that the ferrite core has to be placed inside the case and I wanted the SO239 socket, the ferrite core and the output terminals not all jammed together. So the SO239 socket was not going to be in the center. For this my new caliper was a useful tool and I measured the inside size and the wanted location of the socket. And I figured out I could drill a 16mm hole and the SO239 socket would fit inside while leaving enough room for the mounting flange.

Holes were drilled and things worked out fine, so the SO239 socket is now mounted. After checking the future location I realized I will have to mount the balun with the SO239 socket facing downwards because the antenna cable is quite heavy. This has to be taken into account with the next steps.

Other parts of this project:

Tags: , ,
2018-04-04 Building my own balun, part 2: measuring the 'old' balun 2 years ago
Fritzel balun SWR scan 1-60 MHz 20180325
Fritzel balun SWR scan 1-60 MHz 20180325
Fritzel balun SWR scan 10 meter band 20180325
Fritzel balun SWR scan 10 meter band 20180325
Fritzel balun SWR scan 20 meter band 20180325
Fritzel balun SWR scan 20 meter band 20180325
Since I want to replace a balun that has been up there for ages I want to be able to compare the two. So I used the antenna analyzer to get graphs of the SWR over the whole possible range (1-60 MHz) and on the amateur bands it was built for: the 10 meter band and the 20 meter band.

There was a very interesting difference with the earlier results on the 10 meter band when I first tested the SARK100 antenna analyzer from Linux. The 10 meter band dipole probably moved a bit or something else changed.
Read the rest of Building my own balun, part 2: measuring the 'old' balun

Tags: , ,


, reachable as koos+website@idefix.net. PGP encrypted e-mail preferred.

PGP key 5BA9 368B E6F3 34E4 local copy PGP key 5BA9 368B E6F3 34E4 via keyservers pgp key statistics for 0x5BA9368BE6F334E4 Koos van den Hout
RSS
Other webprojects: Camp Wireless, wireless Internet access at campsites, The Virtual Bookcase, book reviews
This page generated by $Id: morenews.cgi,v 1.46 2019/10/20 15:42:02 koos Exp $ in 0.029353 seconds.